LS3 E-ROD

430HP @5,900 RPM / 425 LB-FT TORQUE @4,600 RPM
price: $8,962
part number: 19369331
Contact Us Add to Cart Catalog

    Direct form the Camaro SS to your project vehicle The LS3 6.2L is the 430-hp standard engine in the Chevrolet Corvette and is a fantastic combination of high technology and uncompromising performance. Our LS3 crate engine comes complete, from the Corvette-specific oil pan to the ignition system. It also includes the EFI intake manifold assembly with injectors and throttle body, exhaust manifolds, water pump, balancer, 58X reluctor wheel, and 14-inch automatic transmission flexplate. Inside, the LS3 is filled with components designed for high performance and longevity. The aluminum block is filled with a sturdy reciprocating assembly that combines with L92-type rectangular-port heads to deliver a 10.7:1 compression ratio. A high-lift, hydraulic roller camshaft delivers a whopping 0.551-inch of lift on the 2.16-inch intake valves and 0.522-inch lift on the 1.59-inch exhaust valves, enhancing the LS3’s tremendous airflow and broad torque curve. The Corvette oil pan doesn’t suit all installation applications. Use a vehicle-specific oil pan for original LS-powered vehicles or Chevrolet Performance’s Muscle Car Oil Pan Kit for older versions.

    • CARB EO#: D-126-32
    • Horsepower: 430 @ 5,900 rpm
    • Torque: 425 lb.-ft. @ 4,600 rpm
    Rated at a strong 430 hp, the original E-ROD crate engine delivers big power with California emissions compliance for countless pre-1995 cars, trucks and SUVs. Along with great power, its aluminum block and heads, and composite intake manifold make it a lightweight performer, too, meaning your project vehicle will likely enjoy weight balance – with less weight over the front axle. We recommend the 4L65-E transmission to match with the E-ROD LS3, which Chevrolet Performance also offers as an inclusive Connect & Cruise E-ROD crate powertrain system.

    To facilitate a complete E-ROD installation, the builder will need to source additional components to complete the assembly and get the vehicle running, including:
    • Fuel tank
    • Fuel lines (re-circulating or returnless)
    • Fuel pump – 58 psi (400 kPa) for LC9 and LS3 or 65 psi (450 kPa) for LSA
    • Fuel tank vent line from the tank to the evaporative emissions canister
    • Purge line from the canister to the engine purge solenoid
    • Air induction system that incorporates the mass airflow sensor
    • Exhaust system behind the catalytic converters.

    All E-ROD engines require a front-end accessory drive system suitable to the vehicle. The instruction manual included with each kit offers recommendations for the accessory drive kit, as well as the transmission, gear ratios and more. Chevrolet offers several configurations of accessory drive systems to suit different applications; and each allows the installer to easily delete air conditioning.

    Chevrolet Performance recommends the LS1 Engine Installation Guide P/N 88959384, which illustrates basic procedures and offers helpful tips on installing an LS engine into older vehicles.

    E-ROD systems do not come with a transmission. Chevrolet Performance recommends the SuperMatic™ 4L70-E – P/N 19244043 – four-speed automatic overdrive transmission, along with Chevrolet Performance’s SuperMatic™ transmission controller for LC9 and LS3 systems. The LSA, with higher torque output, should use the SuperMatic™ 4L85-E, P/N 19300175, along with the SuperMatic™ transmission controller.

Disclaimer: Vickar Community Chevrolet reserves the right to withdraw, change, modify or cancel this powertrain promotion program, any placed or in progress orders and the prices advertised at any time for any reason without prior written notice. Final decisions in all matters relating to the interpretation of any rule or aspect of this program rest solely with Vickar Community Chevrolet.